NACE-CIP1-001 valid test discount voucher

NACE NACE-CIP1-001 Real 2026 Braindumps Mock Exam Dumps

NACE-CIP1-001 Exam Questions | Real NACE-CIP1-001 Practice Dumps

To prepare for the NACE-CIP1-001 exam, candidates can attend training courses offered by NACE or other training providers. These courses cover the topics tested on the exam and provide hands-on training in coating inspection techniques. Candidates can also study independently using study materials provided by NACE or other sources. It is recommended that candidates have a minimum of six months of experience in the coatings industry before taking the exam.

NO.15 Stripe coats are best applied by:

Airless spray

Conventional spray

High volume low pressure spray

Brush

NO.16 The least effective method of surface cleaning is most likely

water blasting.

dry grit blasting.

hand tool cleaning.

power tool cleaning.

NO.17 Inspector’s daily reports are used:
Select All That Apply

By the contractor to estimate the amount of work done that day

To provide continuity between inspectors

To aid in arbitration between the contractor and client

To help in cases of a coating failure

NO.18 Galvanic corrosion occurs on which of the following substrates:

Concrete

Fiberglass Reinforced Plastic

Metal

Wood

NO.19 Polymerization is the process of:

Monomers telegraphing

Monomers joining together

All thermoplastic coatings

All organic coatings

NO.20 You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:

Advise the Contractor he cannot proceed

Advise the Contractor he can proceed

Advise the Contractor of your readings

Call your supervisor

NO.21 A magnetic pull-off type gauge is a good choice when:

Accuracy is not required

When an intrinsically safe tool is required

Performing an adhesion test

When working on non-ferrous metals

NO.22 ISO SA 3 is directly equivalent to:

NACE No. 1/SSPC SP 5

NACE No. 2/SSPC SP 10

NACE No. 3/SSPC SP 6

None of the above

NO.23 Passivation can best be described as:

A protective metallic oxide surface layer that slows corrosion

Complete elimination pf the corrosion process

A coating layer applied to the surface to inhibit corrosion

Treating metal with a liquid inhibiter

NO.24 NACE Level 1 Inspectors have been trained to perform:

All types of inspection

Visual inspection and Non-destructive testing

Visual inspection, Non-Destructive and Destructive testing

Visual inspection only

NO.25 What is used to determine compressed air cleanliness?

Needle pressure gauge

Psychrometer

Blotter test

Profilometer

NO.26 According to SSPC PA 2 a Spot Measurement is:

A single gauge reading

The average of gauge readings taken in a 4cm (1.5 inch) circle

The overall average of all readings

The average of all spot measurements in a given area

NO.27 Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply

Failing to determine the base metal reading (BMR)

Rotating the dial too fast when taking measurements

Taking measurements too far from the edge of a surface

Measuring ditty, tacky, or soft films

NO.28 When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:

Chloride salt may produce a false positive

Synthetic oil or grease may not be identified

Ultra-Violet light may contaminant the surface

Presence of weld spatter may produce a false positive

NO.29 You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners’ representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

Carefully review the document and do the best you can

Minimize your lack of understanding and go ahead with the inspection task to the best of your ability

Advise the owners’ representative of your lack of knowledge in this area

Hire a third patty to assist you in understanding the document

NO.30 Prior to using Inspection Tools the inspector must:

Ensure the instrument is within calibration parameters

Be trained on how to use the instrument

Read the manufactures’ instructions

a), b) & c)

NO.31 You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?

105 Gauge Readings resulting in 35 Spot Measurements

75 Gauge Readings resulting in 25 Spot Measurements

225 Gauge Readings resulting in 75 Spot Measurements

45 Gauge readings resulting in 15 Spot Measurements

Loading …

Verified NACE-CIP1-001 Exam Dumps Q&As – Provide NACE-CIP1-001 with Correct Answers: https://www.trainingdump.com/NACE/NACE-CIP1-001-practice-exam-dumps.html

Tag NACE-CIP1-001 valid test discount voucher

NACE NACE-CIP1-001 Real 2026 Braindumps Mock Exam Dumps [Q15-Q31]