D-PSC-MN-01 valid study materials - Latest Training Dumps

NEW QUESTION 34
In PowerScale hardware maintenance, why is it essential to track the installation and maintenance of FRUs?

To maintain a detailed inventory for audit purposes

To ensure optimal data placement within the cluster

To facilitate future software upgrades

To provide a history for troubleshooting and diagnostics

NEW QUESTION 35
A platform engineer is tasked with adding F600 nodes to an existing Dell EMC PowerScale cluster. After racking and stacking the F600 nodes, they determine that the cluster contains X210 and H400 nodes.
What should the platform engineer consider?

H400 nodes cannot co-exist with the F600 nodes in the same cluster

The F600 must use InfiniBand for internal network communication

F600 nodes cannot co-exist with X210 nodes in the same cluster

The cluster must be upgraded to Ethernet back-end topology

NEW QUESTION 36
What is done with the components when a Gen6 single node is replaced?

Transferred to the new node

Returned to Dell

Sent to WWFA

NEW QUESTION 37
What is a crucial preliminary task before performing any hardware maintenance on a PowerScale cluster?

Disabling access to user shares

Verifying the cluster’s data integrity

Ensuring all software applications are stopped

Checking for hardware warranty coverage

NEW QUESTION 38
During the replacement of a failed hard drive, a key FRU, what steps should be followed to ensure proper installation?

Verifying the drive firmware version matches the cluster

Ensuring the node is isolated from the network

Performing a full data backup

Confirming the slot and drive compatibility

NEW QUESTION 39
A platform engineer plans to set up a rack system for a Dell PowerScale cluster installation.
What is a requirement for the initial setup?

The rack system must have twelve independent 200-240 V power sources.

Power cords must be connected to four power distribution units within the rack cabinet.

The rack cabinet must have at least dual power supplies with power distribution.

Grounding lugs must be used for internal grounding within the chassis.

NEW QUESTION 40
What type of NIC is used for the external network on a Dell EMC PowerScale F600 node?

1 GbE

10 GbE

25 GbE

40 GbE

NEW QUESTION 41
A platform engineer is creating a new Dell EMC PowerScale cluster that must meet SEC 17a-4f rules. Node 1 is powered on and cabled.
What action is needed to meet the requirement?

Activate the Enterprise mode license

Create a new cluster

Reboot into SmartLock Compliance mode

Configure the network

NEW QUESTION 42
When configuring a PowerScale cluster for Hadoop integration, what are key considerations?

Choosing the right HDFS protocol

Configuring data protection for Hadoop directories

Allocating sufficient resources for Hadoop services

Ensuring network optimization for Hadoop traffic

NEW QUESTION 43
A platform engineer is adding three F600 nodes to a Dell PowerScale cluster.
What is a good practice when adding the nodes?

Wait 5 minutes between each additional node.

Manually reboot each node before joining.

Use the isi network output to show progress.

Join new nodes simultaneously.

NEW QUESTION 44
What type of privileges are required to perform tenant-specific administration?

Zone role-based access control

System root privileges

System admin privileges

Role-based access control

NEW QUESTION 45
A Dell PowerScale platform engineer is on site to perform a node replacement. The serial number on the tag does not match the serial number provided by the customer. The platform engineer suspects the tag is incorrect.
Which command can they run to obtain the serial number of the node?

isi devices | grep SerNo

isi status -q

isi_nodes %<id> %<name>

isi_hw_status -i

NEW QUESTION 46
A platform engineer is installing a fully populated Dell PowerScale Gen 6 chassis in a customer rack.
However, the equipment lift is broken.
What is the appropriate course of action to take before attempting to lift the chassis?

Remove the power supplies and hard drives, then rack the chassis.

Remove the power supplies and drive sleds while waiting for the lift to be repaired.

Stop work until the lift is repaired and fully functional.

Remove and label the drive sleds and compute modules, then rack the chassis with assistance.

NEW QUESTION 47
What are essential steps when creating a new PowerScale cluster?

Configuring network settings

Assigning cluster name and IP pool

Setting up data protection levels

Enabling compliance features

NEW QUESTION 48
What is an important consideration when connecting Dell PowerScale Gen6 nodes to external power?

Cable each node in a node pair to a different PDU.

Cable all nodes to the external power feeds before connecting switch power cables.

The total power load for all nodes in the rack should not exceed 100% of the branch circuit rating.

Connect both cables of each node to different external power feeds.

NEW QUESTION 49
When setting up internal networking for a PowerScale cluster, what is a crucial requirement?

Public IP addresses for all nodes

Private interconnects between nodes

Unrestricted internet access

Serial connection between nodes

NEW QUESTION 50
A platform engineer is installing a Dell PowerScale cluster with 12 F200 nodes. They are using breakout cables.
What is the speed of the back-end port of the nodes if the switchport is 100 GbE?

10 GbE

25 GbE

12.5 GbE

50 GbE

NEW QUESTION 51
In the context of PowerScale, what is the purpose of the SRS tool?

To simulate cluster workloads for capacity planning

To provide remote support and diagnostic capabilities

To manage Hadoop data workflows

To enforce data retention policies

NEW QUESTION 52
What is the purpose of SolVe Desktop?

Gather logs from the cluster for analysis

Perform pre-upgrade checks on the cluster

Provide centralized access to step-by-step procedures

Provide access to the latest OneFS codes and firmware upgrades

NEW QUESTION 53
A platform engineer is installing a Dell EMC PowerScale cluster with 12 F200 nodes.
What is the correct ratio used for the breakout cable?

1:2

1:4

1:8

1:10

NEW QUESTION 54
A platform engineer must replace a failed chassis on a Dell PowerScale Gen6 cluster. What must the engineer do after powering off the nodes?

Remove the drive sleds, label them for identification, and place the drive sleds In the newly installed chassis.

Remove the drive sleds and motherboard and transfer them to the new chassis.

Remove the drives and compute modules and reimage each drive before installing them in the chassis.

Remove the drives, install the chassis, and place the drives in the new chassis.

NEW QUESTION 55
Which action is critical when preparing the site for a PowerScale installation?

Setting up remote monitoring tools

Ensuring appropriate environmental conditions, such as temperature and humidity

Configuring the initial cluster network settings

Preparing an inventory of all software applications to be used

NEW QUESTION 56
A customer is planning to add a node to a Dell PowerScale cluster running OneFS 9.0.
Which command can they use from the CLI?

isi devices node add –serial-number=<SN>

isi devices -add

isi node add –node-lnn

isi devices node add –node-lnn

Tag D-PSC-MN-01 valid study materials

[Sep 14, 2025] Pass D-PSC-MN-01 Review Guide, Reliable D-PSC-MN-01 Test Engine [Q34-Q56]