Tag D-PE-OE-23 reliable test cost

NO.18 What is indicated when the Mid-Bay hard drive LED indicator is solid amber?

NO.19 A server in an unattended remote site powers down unexpectedly. The technician assigned to the customer cannot arrive on-site until tomorrow. The customer needs the server back up and running today.
What should the technician do?

NO.20 A system administrator observes network connectivity issues with their iDRACs.
Which three commands can be used in the Diagnostic Console to troubleshoot this issue?
(Select 3)

NO.21 Refer to the exhibit.

A technician it installing an OS to a server. The OS array is 2.8TBs. The OS install is unable to start.
What should the technician do to install the OS?

NO.22 The Dell PowerEdge server uses SEDs. The server is being repurposed for a new solution, and the data on the drives must be permanently deleted.
How can this be accomplished?

NO.23 A technician needs to configure the Lifecycle Controller network settings with a static IP address. A limited number of static IP addresses are available for use.
Which previously assigned IP address can also be used for the Lifecycle Controller?

NO.24 A server has both processor sockets populated. An adapter card in the server is not functioning.
However, no errors are displayed. The technician reboots the server, enters the System Setup utility, and selects System BIOS.
What should the technician do before replacing the adapter card?

NO.25 What image does the iDRAC9 BIOS/UEFI Recovery feature use to flash a corrupt BIOS?

NO.26 How can a system administrator compare the currently installed hardware to the original system configuration?

NO.27 Which type of access is known as Firmware RACADM on a Dell EMC PowerEdge server?

NO.28 Which operation should a technician perform to ensure configuration recovery if a server must be physically replaced?

NO.29 SPECIAL INSTRUCTIONS
The remaining Part1 questions are associated with four case studies that describe various environments or settings. Each case study appears on its own display screen. Questions for each case study will appear on separate display screens. When displaying a question, you can easily review the related case study by clicking on the ‘Review Case Study’ icon shown below:
Case Study 5 – Refer to the Exhibit.

Backing up data from a Dell EMC Isilon cluster exceeds the company’s backup window. Because the company has a large amount of data with a continuous high growth rate, they want to change their backup strategy. The Gen 6 Isilon cluster consists of 24 nodes.
Their current backup strategy is an NDMP three-way backup performing weekly full backups to tape and incremental backups each night. The strategy uses Dell EMC Net Worker. The DMA uses Include paths to specify what data to backup. All data on the cluster must remain accessible.
The company’s IT team is now looking for a method to increase the performance of their backups. After some investigations, you notice that the backup job quiesces the file system. This is creating lock contention issues on open files and not allowing users full access to data when the backup job runs.
What advice should be provided to the team to eliminate lock contention and allow full access to users?

NO.30 iDRAC9 System Lockdown Mode is enabled.
In addition to the Power cap setting and System power operations, which settings can an administrator access?

NO.31 What is required for iDRAC Direct 2.0 to connect with IDRAC9 interfaces such as RACADM and WSMAN?

NO.32 Which option is a granular user privilege configurable in the iDRAC9?

NO.33 A technician creates two virtual disks and assigns a dedicated hot spare to each virtual disk. The technician also creates a global hot spare. A drive fails on the second virtual disk.
What is the result?

NO.34 A server has a dead system board that a technician must replace. After replacing the new system board the technician finds that the user did not back up the server profile, although they did configure the Parts Replacement policy to restore the configuration and firmware revisions for any replaced parts.
After powering on the server with the new system board, the Easy Restore feature displays a window asking if the Easy restore configuration needs to be restored to the system board.
As the Parts Replacement policy had already been configured, the technician selects YES at the Easy Restore screen knowing that the parts Replacement policy will restore the remaining configurations. After powering on the server, the technician then finds that the parts not covered by Easy Restores have not been reconfigured.
What caused the reconfiguration process to stop?

NO.35 A technician is configuring the server to boot to the Internal Dual SD Module.
Which BIOS boot option should the technician select?

NO.36 A system administrator plans to use a remote desktop that has the DRAC tools installed to run RACADM commands.
Which two CLI options must be in the RACADM command? (Select 2)

NO.37 A user has a fully configured PowerEdge R640 and an iSM installed on their Windows. 2016 operating system. They now want to install OMSA to enable them to have alerts sent out In-Band to a management console.
What does the user need to consider?