Senior-Internal-Corrosion-Technologist

Certification Topics of Senior-Internal-Corrosion-Technologist Exam PDF Recently Updated Questions

Senior-Internal-Corrosion-Technologist Exam Prep Guide: Prep guide for the Senior-Internal-Corrosion-Technologist Exam

NEW QUESTION 61
When using a destructive Paint Inspection Gauge the NACE inspector must:

Determine the Dry Film Thickness of the coating prior to use

Ensure the glue on the dolly is properly applied prior to use

Consult SSPC Guide 1 prior to use

Select the appropriate hand wheel based on the measured Dry Film Thickness prior to use

NEW QUESTION 62
You are the new NACE Level 2 Inspector on a Job which had been very problematic. The previous Inspector was fired due to personality conflicts with the Contractor’s supervisor. Upon arriving onsite the Contractor’s supervisor advises you In no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action Is to:

Challenge the supervisor’s authority

Defend the previous inspector

Express a willingness to work with the site team and follow the specification

Suggest to the Owner that the supervisor should be removed from site

NEW QUESTION 63
Surface preparation methods for Non-ferrous metals are:

The same as for Ferrous metals

The same for all Non-Ferrous metals

Specific for each type of Non-Ferrous metal

Not required

NEW QUESTION 64
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It Is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project.
You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot be found.
You FIRST preferred course of action Is to:

Use creative writing to cover over the fact they are missing

Plainly state in your report that they are missing

EXInot complete your report until they can be found

Re-create the reports as not much was going on during night shift anyway

NEW QUESTION 65
You ate the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no Individual gauge reading shall be below a certain value. As this is not part of the standard you should:

Ignore the additional requirement

Enforce the additional requirement

Call your supervisor

Request clarification from the specifier

NEW QUESTION 66
When performing a hardness test on a coating which has elastic properties the inspector is likely to observe:

A very high reading

A very low reading

Cold (low or creep

No difference from any other coating

NEW QUESTION 67
When observing design defects the NACE Inspector should:

Document the defect and the potential problems that could result

Ignore the defect as the inspector can’t change the design

Request that the item be rebuilt with a better design for coating

Stop the job immediately

NEW QUESTION 68
When observing fabrication defects the NACE Inspector should:

Require they be corrected prior to coating

Consult the specification to determine how they should be treated

Stop the job immediately

Write an NCR and call the fabricator

NEW QUESTION 69
Linings are used on the interior of pipelines to

provide protection against soil chemicals.

afford limited temperature Insulation.

protect the transported product.

reduce magnetic polarity.

NEW QUESTION 70
The coating applicator has ignored a surface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:

Stop the Job

Require the Applicator to remove the applied coating

Advise the Owner and write a Non-Conformance report

Ignore the situation

NEW QUESTION 71
You can use magnifiers to examine all of the following EXCEPT

Surface profile

Surface cleanliness

Blisters

Mill scale

NEW QUESTION 72
When completing the Final Inspection report the Inspector should write the report using:

Language that only technical experts would understand

Language that the most people would understand

Language that only those directly Involved in the project would understand

Language that another NACE Inspector would understand

NEW QUESTION 73
The primary purpose of Fireproofing coatings are to provide:

Fire extinguishing characteristics

Temporary protection for the structure

Preferential fuel for the file

Explosion resistance

NEW QUESTION 74
A failure caused by applying a coating too thinly is known as

failure to cure.

chalking.

cracking.

pinholes.

NEW QUESTION 75
Coating application to concrete substrates is:

More challenging than coating steel

Less challenging than coating steel

The same as coating steel

Not required as concrete is Inorganic

Loading …

2025 New Preparation Guide of AMPP Senior-Internal-Corrosion-Technologist Exam: https://www.trainingdump.com/AMPP/Senior-Internal-Corrosion-Technologist-practice-exam-dumps.html

Category Senior-Internal-Corrosion-Technologist

Certification Topics of Senior-Internal-Corrosion-Technologist Exam PDF Recently Updated Questions [Q61-Q75]