Latest Training Dumps

HOME
Features
About
Services
More
NEW UPDATES
Contact US

Category GB0-191-ENU

Home
Archive by category "GB0-191-ENU"

GB0-191-ENU H3C

GB0-191-ENU Dumps To Pass H3CNE Exam in One Day (Updated 434 Questions) [Q149-Q165]

Oct 1, 2023 TrainingDump 0 Comment

GB0-191-ENU Dumps To Pass H3CNE Exam in One Day (Updated 434 Questions)

GB0-191-ENU Exam Brain Dumps – Study Notes and Theory

H3C GB0-191-ENU exam is intended for IT professionals who have at least two years of experience in network construction and management. Candidates who pass the exam will be recognized as H3C Certified Network Engineers (HCNEs) and will have demonstrated their ability to design and implement small and medium-sized enterprise networks using H3C’s products and technologies.

NEW QUESTION 149
The correct statement below is ______. (Multiple choice)

In the active transfer mode of FTP, the FTP client actively establishes a data connection to the server

In the active transmission mode of FTP, the FTP server actively establishes a data connection to the client

FTP server and client in passive transmission mode use temporary ports to establish data connections

The passive transfer mode of FTP uses the PORT command

The passive transfer mode of FTP uses the PASV command

NEW QUESTION 150
The correct description of the startup process of the router system in the following options is ______.

Memory check —— start bootrom—— application decompression ——- application load

start bootrom—— memory check—— load the application

Decompress the application —— load the application —— start the bootrom —— memory check

Memory detection —— application decompression —— application loading

NEW QUESTION 151
There is a default route in the router’s routing table, its destination network segment and mask are both 0.0.0.0, and its next hop is the router’s S0/0 interface, then the following description of this route is correct. ______. (Multiple choice)

When the router receives a data packet to the destination address 120.1.1.1, if there is no other exact match in the router table, then the data packet will match this default route

The route has the shortest mask, so the data packet will be forwarded according to the default route only if there is no other route matching the data packet

The metric value of this route may be 3

The priority of this route may be 100

NEW QUESTION 152
The following statement about the upgrade of H3C network equipment is correct ______. (Multiple choice)

Use Xmodem to upgrade to the same speed as FTP

When using FTP to upgrade, the device can only be used as an FTP client

When the device cannot boot to the command line mode and needs to upgrade the operating system software, only the Xmodem method can be used

In an environment where the complex interaction between the client and the server is not convenient, you can use TFTP to upgrade

NEW QUESTION 153
An empty-configured MSR router is connected to the same OSPF network through multiple interfaces, and OSPF is enabled on all these interfaces. After the configuration is completed, the router has successfully learned the OSPF routes in the network.
Now run the following command on an OSPF interface of the router:
[MSR-GigabitEthernet0/0]ospf cost 256
In the case of keeping other configurations unchanged, the correct understanding of the configuration is _____.

This configuration may affect the forwarding path of data packets

This configuration will not affect the forwarding path of data packets

The configuration command is invalid because the command was entered incorrectly

This configuration command is invalid because the maximum value of Cost is 255

NEW QUESTION 154
The RIP routing protocol has a timer, which defines the elapsed time for a route from the metric value to 16 until it is deleted from the routing table, then ______.

This timer is Timeout timer

This timer is Garbage-Collect timer

The timer defaults to 120s on the MSR router

The timer defaults to 180s on the MSR router

NEW QUESTION 155
In Windows operating system, which command can display ARP table entry information?

display arp

arp -a

arp -d

show arp

NEW QUESTION 156
The customer’s network connection looks like:
HostA—-GE0/0–MSR-1–S1/0—–WAN—-S1/0–MSR-2–GE0/0—-HostB
On the WAN interface S1/0 of the two routers MSR-1 and MSR-2, only the PPP protocol is encapsulated and the IP address is configured. Currently, HostA and HostB can ping each other. Add the command ppp authentication-mode chap under MSR-1 interface S1/0, and then execute shutdown and undo shutdown operations on S1/0 of MSR-1.
So ______ . (Multiple choice)

At this point, HostA and HostB can still ping each other

At this time, HostA and HostB cannot ping each other

MSR-2 will send a Challenge and send it to MSR-1 along with the local user name to start CHAP authentication

MSR-1 will send a Challenge and send it to MSR-2 with the user name of the local end to start CHAP authentication

NEW QUESTION 157
The following description of the characteristics of the router is correct ______. (Multiple choice)

It is a network layer device

Route and forward according to link layer information

Provide rich interface types

Can support multiple routing protocols

NEW QUESTION 158
On the MSR router, if you want to modify some configuration after logging in to the device at the access level, you can use the ______ command to switch to level 3. (Multiple choice)

super

level 3

password

NEW QUESTION 159
The customer’s routers MSR-1 and MSR-2 are interconnected through their GigabitEthernet0/0, and RIP is running between the two routers. RIP has correctly completed remote routing learning. The following configuration is added on MSR-1: firewall enable acl number 3000 rule 0 deny udp destination-port eq 520 rule 5 permit ip and this ACL is applied to the inbound direction of MSR-1 interface GigabitEthernet0/0. So ______ .

MSR-1 still has the RIP route to the opposite end

MSR-1 cannot learn the RIP route of the opposite end

MSR-2 still has the RIP route to the opposite end

MSR-2 cannot learn the RIP route of the opposite end

NEW QUESTION 160
In the network environment as shown in the figure, two routers are connected back to back by serial ports, and the rate of the interconnection link should be set to 2Mbps. The correct statement below is ______.

It is necessary to determine the interface type and the cable meet the V.24 regulations

Use the baudrate 2048000 command to configure on the synchronization port of RTA

Use the baudrate 2048000 command to configure on the synchronization port of the RTB

Use virtual-baudrate 2048000 command to configure on the synchronization port of RTB

Use bandrate 2048000 command configuration on the synchronization port of RTA, use virtual-baudrate 2048000 command configuration on the synchronization port of RTB

NEW QUESTION 161
A network connection is like:
HostA—-GE0/0–MSR-1–S1/0———S1/0–MSR-2–GE0/0—-HostB
Two MSR routers MSR-1 and MSR-2 are interconnected back-to-back through their S1/0 interfaces, and their GE0/0 interfaces are respectively connected to the client hosts HostA and HostB. The IP address of HostA is 192.168.0.2/24, and the address of the S0/0 interface of MSR-2 is 1.1.1.2/30. By configuring other relevant IP addresses and routes, HostA can communicate with HostB in the current network.
Nowadays, the customer requires that HostA is not allowed to log in to the MSR-2 through Telnet at address 1.1.1.2.
So which of the following configurations can meet this requirement? (multiple choice)

Configure the following ACL on MSR-1 and apply it to the inbound direction of GE0/0 of MSR-1: [MSR-1]firewall enable [MSR-1]acl number 3000 [MSR-1-acl-adv -3000]rule 0 deny tcp source 192.168.0.1 0.0.0.255 destination 1.1.1.2 0.0.0.3 destination-port eq telnet

Configure the following ACL on MSR-1 and apply it to the outbound direction of GE0/0 of MSR-1: [MSR-1]firewall enable [MSR-1]acl number 3000 [MSR-1-acl- adv-3000]rule 0 deny tcp source 192.168.0.2 0 destination 1.1.1.2 0 destination-port eq telnet

Configure the following ACL on MSR-1 and apply it to the inbound direction of S1/0 of MSR-1: [MSR-1]firewall enable [MSR-1]acl number 3000 [MSR-1-acl- adv-3000]rule 0 deny tcp source 192.168.0.1 0.0.0.255 destination 1.1.1.2 0 destination-port eq telnet

Configure the following ACL on MSR-1 and apply it to the outbound direction of S1/0 of MSR-1: [MSR-1]firewall enable [MSR-1]acl number 3000 [MSR-1-acl- adv-3000]rule 0 deny tcp source 192.168.0.2 0 destination 1.1.1.2 0.0.0.3 destination-port eq telnet

NEW QUESTION 162
A DNS client queries the local domain name server for the IP address of www.sina.com.cn, and the local domain name server usually responds by means of DNS query?

Recursive query

Iterative query

Reverse query

Fuzzy query

NEW QUESTION 163
There are many kinds of WAN interfaces. The following description of the WAN interface is wrong.

The V.24 protocol interface can work in both synchronous and asynchronous modes. In the asynchronous mode, the link layer uses PPP encapsulation.

The V.35 protocol interface can work in both synchronous and asynchronous modes. In the asynchronous mode, the link layer uses PPP encapsulation.

BRI/PRI interface is used for ISDN access, the default link encapsulation is PPP

The G.703 interface provides high-speed data synchronous communication services.

NEW QUESTION 164
Two MSR routers MSR-1 and MSR-2 are connected through the WAN and dynamically complete remote route learning through RIPv2.
After stable for 2 minutes, the RIP update message from MSR-2 is received on MSR-1, which contains the route with Cost of 14, then ______. (Multiple choice)

If there is no such route in the routing table of MSR-1, then the route will be added to the routing table of MSR-1

If the routing table of MSR-1 originally has the route, and its Cost is less than 14, then the routing entry on MSR-1 will not be updated

If the routing table of MSR-1 originally has the route, the routing entry will only be updated when its Cost is greater than 14.

If the MSR-1 routing table originally contains the same route received from the neighbor, and its Cost is less than 14, the route will also be updated

NEW QUESTION 165
A company purchased switches from two manufacturers, A and B, for network engineering implementation. Need to use link aggregation technology between the switches of the two vendors. After consulting the relevant documents, it is found that the switch of manufacturer A does not support the LACP protocol.
In this case, which of the following configuration methods are reasonable? (multiple choice)

One party configures static aggregation, and one party configures dynamic aggregation

Both parties configure dynamic aggregation

Both parties configure static aggregation

Unable to use link aggregation

Loading …

GB0-191-ENU Dumps PDF – Want To Pass GB0-191-ENU Fast: https://www.trainingdump.com/H3C/GB0-191-ENU-practice-exam-dumps.html

GB0-191-ENU H3C

Pass H3C GB0-191-ENU exam questions – convert Test Engine to PDF [Q151-Q173]

Jul 5, 2022 TrainingDump 0 Comment

Pass H3C GB0-191-ENU exam questions – convert Test Engine to PDF

Pass Your GB0-191-ENU Exam Easily – Real GB0-191-ENU Practice Dump Updated Jul 05, 2022

Please go to Pass H3C GB0-191-ENU exam questions – convert Test Engine to PDF [Q151-Q173] to view the test

GB0-191-ENU Real Exam Questions and Answers FREE: https://www.trainingdump.com/H3C/GB0-191-ENU-practice-exam-dumps.html