Ace HPE7-A01 Certification with 121 Actual Questions [Q14-Q31]

Rate this post

Ace HPE7-A01 Certification with 121 Actual Questions

PASS HP HPE7-A01 EXAM WITH UPDATED DUMPS

The HP HPE7-A01 exam covers a wide range of topics, including Aruba wireless solutions and technologies, network architecture, security and authentication, troubleshooting, and management. HPE7-A01 exam consists of 60 multiple-choice questions, and candidates have 90 minutes to complete it. The passing score for the exam is 75%. Aruba Certified Campus Access Professional Exam certification is valid for three years, after which the candidate must recertify to maintain their certification status. With this certification, professionals can demonstrate their expertise in Aruba wireless technologies and solutions, which can help them advance their careers and increase their earning potential.

Q14. Match each PoE power class to Its corresponding 802.3 standard. (Options may he used more than once or not at all)

Q15. A company recently upgraded its campus switching infrastructure with Aruba 6300 CX switches. They have implemented 802.1X authentication on edge ports where laptop and loT devices typically connect An administrator has noticed that for PoE devices the pons are delivering the maximum wattage instead of what the device actually needs Upon connecting the loT devices, the devices request their specific required wattage through information exchange

Concerned about this waste of electricity, what should the administrator implement to solve this problem?

Enable AAA authentication to exempt LLDP and/or CDP information

Globally enable the QoS trust setting for LLDP and/or CDP

Create device profiles with the correct power definitions.

implement a classifier policy with the correct power definitions.

Q16. What steps are part of the Key Management workflow when a wireless device is roaming from AP1 to AP2?
(Select two.)

AP1 will cache the client’s information and send it to the Key Management service

The Key Management service receives from AirMatch a list of all AP2’s neighbors

The Key Management service receives a list of all AP1 s neighbors from AirMatch.

The Key Management service then generates R1 keys for AP2’s neighbors.

A client associates and authenticates with the AP2 after roaming from AP1

Explanation
The correct steps that are part of the Key Management workflow when a wireless device is roaming from AP1 to AP2 are A and D.
A: AP1 will cache the client’s information and send it to the Key Management service. This is true because when a client associates and authenticates with AP1, AP1 will generate a pairwise master key (PMK) for the client and store it in its cache. AP1 will also send the PMK and other client information, such as MAC address, VLAN, and SSID, to the Key Management service, which is a centralized service that runs on Aruba Mobility Controllers (MCs) or Mobility Master (MM) devices1. The Key Management service will use this information to facilitate fast roaming for the client.
D: The Key Management service then generates R1 keys for AP2’s neighbors. This is true because when the Key Management service receives the client information from AP1, it will use the PMK to derive R0 and R1 keys for the client. R0 keys are used to generate R1 keys, which are used to generate pairwise transient keys (PTKs) for encryption. The Key Management service will distribute the R1 keys to AP2 and its neighboring APs, which are determined by AirMatch based on RF proximity2. This way, when the client roams to AP2 or any of its neighbors, it can skip the 802.1X authentication and use the R1 key to quickly generate a PTK with the new AP3.
B: The Key Management service receives from AirMatch a list of all AP2’s neighbors. This is false because the Key Management service does not receive this information from AirMatch directly. AirMatch is a feature that runs on MCs or MM devices and optimizes the RF performance of Aruba devices by using machine learning algorithms. AirMatch periodically sends neighbor reports to all APs, which contain information about their nearby APs based on signal strength and interference. The APs then send these reports to the Key Management service, which uses them to determine which APs should receive R1 keys for a given client2.
C: The Key Management service receives a list of all AP1 s neighbors from AirMatch. This is false for the same reason as B. The Key Management service does not receive this information from AirMatch directly, but from the APs that send their neighbor reports.
E: A client associates and authenticates with the AP2 after roaming from AP1. This is false because a client does not need to authenticate with AP2 after roaming from AP1 if it has already authenticated with AP1 and received R1 keys from the Key Management service. The client only needs to associate with AP2 and perform a four-way handshake using the R1 key to generate a PTK for encryption3. This is called fast roaming or
802.11r roaming, and it reduces the latency and disruption caused by full authentication.1: ArubaOS 8.7 User Guide 2: ArubaOS 8.7 User Guide 3: ArubaOS 8.7 User Guide : ArubaOS 8.7 User Guide

Q17. A customer wants to provide wired security as close to the source as possible The wired security must meet the following requirements:
-allow ping from the IT management VLAN to the user VLAN
-deny ping sourcing from the user VLAN to the IT management VLAN
The customer is using Aruba CX 6300s
What is the correct way to implement these requirements?

Apply an outbound ACL on the user VLAN allowing temp echo-reply traffic toward the IT management VLAN

Apply an inbound ACL on the user VLAN allowing icmp echo-reply traffic toward the IT management VLAN

Apply an inbound ACL on the user VLAN denying icmp echo traffic toward the IT management VLAN

Apply an outbound ACL on the user VLAN denying icmp echo traffic toward the IT management VLAN

Q18. For the Aruba CX 6400 switch, what does virtual output queueing (VOQ) implement that is different from most typical campus switches?

large ingress packet buffers

large egress packet buffers

per port ASICs

VSX

Q19. What are the requirements to ensure that WMM is working effectively’? (Select two)

The APs and the controller are Wi-Fi CERTIFIED for WMM which is enabled

All APs need to be from the AP-5xx series and AP-6xx series which are Wi-Fi CERTIFIED 6.

The Client must be Wi-Fi CERTIFIED for WMM and configured for WMM marking.

The Aruba AOS10 APs installed have to be converted to controlled mode

The AP needs to be connected via a tagged VLAN to the wired port

Q20. Which feature supported by SNMPv3 provides an advantage over SNMPv2c?

Transport mapping

Community strings

GetBulk

Encryption

Q21. With the Aruba CX 6000 24G switch with uplinks of 1/1/25 and what does the switch do when a client port detects a loop and the do-not-disabie parameter is used?

Port status will be validated once status is cleared

An event log message is created.

The network analytics engine is triggered.

Port status led blinks in amber with 100hz.

Q22. Refer to the exhibit.

With Core-1. what is the default value for config-revision?

1-0

0. 0

Q23. List the WPA 4-Way Handshake functions in the correct order.

Q24. A customer has a large number of food-producing machines
* All machines are connected via Aruba CX6200 switches in VLANs 100.110. and 120
* Several external technicians are maintaining this special equipment
What are the correct commands to ensure that no rogue DHCP server will impact the network?

Q25. Which statements regarding Aruba NAE agents are true? (Select two )

A single NAE script can be used by multiple NAE agents

NAE agents are active at all times

NAE agents will never consume more than 10% of switch processor resources

NAE scripts must be reviewed and signed by Aruba before being used

A single NAE agent can be used by multiple NAE scripts.

Q26. A customer has a large number of food-producing machines
* All machines are connected via Aruba CX6200 switches in VLANs 100.110. and 120
* Several external technicians are maintaining this special equipment
What are the correct commands to ensure that no rogue DHCP server will impact the network?

Q27. Which statements are true regarding a VXLAN implementation on Aruba Switches? (Select two.)

MTU size must be increased beyond the default

VNIs encapsulate and decapsulate VXLAN traffic

VTEPs encapsulate and decapsulate VXLAN traffic

They are only available for datacenter switches (CX 8k, 9k,10k)

All Aruba CX switches support VXLAN.

Q28. A company deployed Dynamic Segmentation with their CX switches and Gateways After performing a security audit on their network, they discovered that the tunnels built between the CX switch and the Aruba Gateway are not encrypted. The company is concerned that bad actors could try to insert spoofed messages on the Gateway to disrupt communications or obtain information about the network.
Which action must the administrator perform to address this situation?

Enable Secure Mode Enhanced

Enable Enhanced security

Enable Enhanced PAPI security

Enable GRE security

Q29. What are the requirements to ensure that WMM is working effectively’? (Select two)

The APs and the controller are Wi-Fi CERTIFIED for WMM which is enabled

All APs need to be from the AP-5xx series and AP-6xx series which are Wi-Fi CERTIFIED 6.

The Client must be Wi-Fi CERTIFIED for WMM and configured for WMM marking.

The Aruba AOS10 APs installed have to be converted to controlled mode

The AP needs to be connected via a tagged VLAN to the wired port

Q30. You need to have different routing-table requirements with Aruba CX 6300 VSF configuration Assuming the correct layer-2 VLAN already exists how would you create a new OSPF configuration for a separate routing table?

Create a new OSPF area, and attach VRF name.

Create a new OSPF process ID with vrf name.

Attach a new OSFP process ID with a custom routing table

Attach OSPF process ID in the VRF configuration.

Q31. In an ArubaOS 10 architecture using an AP and a gateway, what happens when a client attempts to join the network and the WLAN is configured with OWE?

Authentication information is not exchanged

The Gateway will not respond.

No encryption is applied.

RADIUS protocol is utilized.

The Aruba Certified Campus Access Professional certification exam is a performance-based exam that tests the candidate’s ability to solve real-world problems in wireless networking. HPE7-A01 exam is designed to evaluate the candidate’s knowledge and skills in designing and configuring Aruba wireless networks, including the ability to troubleshoot and optimize the network. Candidates are required to demonstrate their proficiency in configuring and managing Aruba access points, mobility controllers, and network management tools.

HPE7-A01 Questions PDF [2024] Use Valid New dump to Clear Exam: https://www.trainingdump.com/HP/HPE7-A01-practice-exam-dumps.html

Ace HPE7-A01 Certification with 121 Actual Questions [Q14-Q31]

Ace HPE7-A01 Certification with 121 Actual Questions [Q14-Q31]

TrainingDump

Leave a Reply
Cancel reply

Leave a Reply

Ace HPE7-A01 Certification with 121 Actual Questions [Q14-Q31]

TrainingDump

Leave a Reply Cancel reply

Leave a Reply

Leave a Reply
Cancel reply