300-425 - 最新培训试卷

Try 100% Updated 300-425 Exam Questions [2026]

Pass 300-425 Exam – Real Questions and Answers

To prepare for the Cisco 300-425 certification exam, candidates are advised to take a training course that covers the exam material in detail. There are many training courses available, both online and in-person, that can help candidates to prepare for the exam. Additionally, candidates can also take advantage of study guides, practice exams, and other resources to help them prepare for the exam.

Q28. An engineer is designing a new wireless network. The network needs to meet these requirements:

Which design approach should be taken?

5 GHz frequency band with channel bonding, to support 40 MHz channels

5 GHz frequency band without channel bonding, to support 20 MHz channels

5 GHz frequency band with channel bonding, to support 80 MHz channels.

2.4 GHz frequency band without channel bonding, to support 20 MHz channels

Q29. Which statement about the 9800 Series Wireless Controller mobility tunnel on a Cisco Catalyst 9800 controller is true?

It is an IPsec tunnel with control path only.

It is a CAPWAP tunnel with data path only.

It is a CAPWAP tunnel with control path and data path.

It is an IPsec tunnel with control path and data path.

Q30. Why is Dynamic Frequency Selection (DFS) important in WLAN design?

To allow use of radar-detected channels in 2.4 GHz

To increase AP transmit power beyond regulations

To enable usage of additional 5 GHz channels while avoiding radar interference

To reduce co-channel interference on 6 GHz

Q31. Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?

UDP 16666 for control plane, EoIP (IP protocol 97) for data plane

UDP 16668 for control plane, UDP 16667 for data plane

UDP 16667 for control plane, UDP 16666 for data plane

UDP 16666 for control plane, UDP 16667 for data plane

Q32. Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)

PoE battery

spirit level

access point

tall tripod

goggles

ladder

Q33. A customer asks an engineer to explain the concept of mobility domains and mobility groups. Which statement does the engineer respond with?

A mobility group does not constrain the distribution of security context of a client and also does not constrain AP fail-over between controllers when the WLC are in the same mobility domain.

If WLCs are in the same mobility domain, they communicate with each other but, if an anchor WLC is present it must be in the same mobility domain for communication to be possible.

If WLCs are in the same mobility domain, they communicate with each other. Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.

WLCs do not need to be in the same mobility domain to communicate with each other. Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.

Q34. A customer is running a guest WLAN with a foreign/export-anchor setup. There is one anchor WLC in the US and two in Europe. Anchor WLC priorities are used to prefer local anchors. During a routine network audit, it is discovered that a large number of guest client sessions in the US are anchored to the WLCs in Europe.
Which
reason explains this behavior?

The foreign WLC failed and recovered.

The US anchor WLC failed and recovered.

The US anchor WLC is anchored to itself with a priority value of zero.

The anchor WLC is in the same mobility group.

Q35. After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data. What does this indicate about the signal strength?

The area is below -67 dBm at coverage cell edge.

The area is below -100 dBm at coverage cell edge.

The area is below the minimum threshold configured on the tool.

The area is below the detectable level and indicates no RF signal.

Q36. An engineer must produce a passive survey report. The coverage heat map shows the entire site with all signal levels. To see only the desired coverage, which action must the engineer take?

Change the color scheme to show the desired heat map.

Use the RSSI calibration tool to configure the receiver sensitivity.

Use the RSSI slider to set the heat map to the desired cutoff filter.

Filter the results to show the desired APs only.

Q37. A company has a Cisco WLC that runs AireOS 8.3 code. A WLAN must be dedicated to mobile devices running iOS 10 or later. Which WLAN feature must be used for this requirement?

Adaptive 802.11r

802.11v

802.11k

802.11i

Q38. An engineer is configuring a centralized set of controllers for separate facilities. Which two Cisco wireless architectures must be used to ensure flexible sizing of WLAN to VLAN mappings?
(选择两个）。

interface group

mobility group

AP 小组

controller group

RF group

Q39. A customer called with a requirement that internal clients must be on different subnets depending on the building they are in All access points are operating in local mode and will not be modified, and this is a single controller solution Which design approach creates the desired result?

Create AP groups for each desired location, map the correct VLANs to the internal SSlD and add the access prints for that location

Create an SSID. place it to the desired VLAN under WLANs. and configure 802.ix in ISE to assign the correct VLAN based on the SSlD from which the client is authenticating.

Create FiexConnect groups, place the access points in. and set the correct VLAN to SSlD mapping based on location.

Create mobility anchors for the SSID. and on the controller under the internal SSID. create a foreign map to the desired VLAN based on location

Q40. A consulting engineer is preparing to survey a brownfield deployment for a 6000-sqft building with four floors that have APs. The entire building is being remodeled and the furniture, office walls, and decoration are being updated. The engineer must perform a survey analysis on the potential RF impact of newer furniture materials. How must the survey be conducted?

Evaluate the neighbor APs strength and density based on the radio statistics information of each AP.

Measure upstream and downstream data rates based on the remodeling of the building.

Use a survey tool with the existing AP positions using building floor maps and material configuration.

Perform a sweep analysis first to predict the signal strength across each point in a floor.

Q41. 关于创建移动组，不包括移动锚点，哪种说法是正确的？

每个 WLC 必须使用相同的移动名称，并在对方的静态移动成员列表中被定义为对等网络。

如果部署了具有 HA SSO 的 WLC，则 WLC HA 对中的每个 WLC 都会被单独视为移动对等设备。

要成为移动组的成员，WLC 不必具有相同的型号或类型，但每个成员都应运行不同的软件版本。

移动组不要求组内所有 WLC 使用相同的虚拟 IP 地址。

Q42. A customer deploys a new Cisco high-density wireless network within the open areas of a mall to provide free public wireless on 5 GHz. The existing mall tenants have their own wireless networks that are independently managed. Which design approach minimizes channel utilization for the public network?

Enable all 5-GHz channels that are supported by the region and use 40-MHz channels.

Enable UNII-1 channels only and use 80-MHz channels.

Enable UNII-1 channels only and use 20-MHz channels.

Enable all 5-GHz channels that are supported by the region and use 20-MHz channels.

Cisco 300-425 certification exam is part of the Cisco Certified Network Professional (CCNP) Enterprise certification program, which is a professional-level certification that validates a professional’s ability to plan, implement, verify, and troubleshoot local and wide-area enterprise networks. Designing Cisco Enterprise Wireless Networks certification is highly sought after by IT professionals who want to advance their careers in network design and implementation, as the CCNP Enterprise certification is recognized globally as a standard of excellence in the networking industry.

300-425 Exam Questions Get Updated [2026] with Correct Answers: https://www.trainingdump.com/Cisco/300-425-practice-exam-dumps.html

免费思科 300-425 模拟考试题库 [2022 年 11 月 19 日］

300-425 数据包 PDF 和认证培训

思科 300-425 认证考试有哪些优势

获得CCENT认证的个人在IT工作中将比同行更具优势。雇主会将 CCENT 认证作为筛选潜在应聘者的标准。获得思科认证入门网络技术员（CCENT）认证的优势之一是它得到了包括思科和微软在内的许多公司的认可。因此，该认证可以增加您在 IT 行业的就业机会，因为它是最受雇主欢迎的认证之一。该考试旨在评估您执行与网络工程师相关的所有任务的能力。因此，该认证与 Cisco CCNA R&S 认证一样有价值。获得 CCENT 认证的人员也有资格申请更高级的认证，如网络工程师认证（Network Engineer）、网络工程师认证（Network Engineer）和网络工程师认证（Network Engineer）。

请访问 [Q31-Q53] Dumps for Free Cisco 300-425 Practice Exam Questions [Nov 19, 2022] 查看测试内容

思科 300-425 测试涉及为企业创建思科无线网络。您可以从称为集中的六项测试中选择它。这种考试本身有助于获得思科认证专家-企业无线设计认证。此外，由于它是在 350-401 核心测试之后进行的，因此成功通过它意味着您可以获得 CCNP 企业证书。

您可以使用哪些学习指南来学习 300-425 专题？

思科出版社通过专家编写的书籍为 300-425 考试考生提供支持。CCNP Enterprise Wireless Design 300-425》是官方指南，可帮助考生在最终考试中取得成功。本书作者是罗伯特-巴顿、杰罗姆-亨利和大卫-胡卡比。这些无线网络专家编写的这本书内容精彩，涉及思科 300-425 考试的各个方面。本书还涵盖了 300-430 考试的要求，这是另一项集中考试。本书对每个主题的内容都进行了权威性的解释，同时还使用了实际案例，让你对这些内容有正确的认识。特别是，它深入探讨了无线网络的所有层级，并提供了真实的试卷供练习。以下是这本优秀学习指南的更多内容：

最后一章涉及备考，通过资源和工具为您提供指导，帮助您制定复习内容和参加期末考试的策略。
基于在线的交互式闪存卡，确保你知道如何应用每章的关键概念；
每章末尾都有专题重点表格，让您能够掌握官方考试的核心概念；
通过测验，您可以决定用多长时间讲完每个章节；
详尽的绩效报告；
考试复习常规已被证实有助于取得良好的考试成绩；

300-425 考试考生可能希望使用的另一本重要书籍是 思科无线网络设计指南.本学习指南 作者：Shaun Hummel 亚马逊上有售，内容涵盖思科网络无线设计的基础知识。简而言之，它深入探讨了一种可以用来规划和设计无线网络的有效方法。该书最适合作为参考书，但也可以作为复习资源的重要补充，用于真正的验证，它仔细研究了无线原理、技巧和技术，同时也是一本实用的网络设计指南。书中还包括一个案例研究，以帮助读者了解实际情况和应对策略。读者还可以适当利用章节测验来评估自己对内容的吸收情况。

检查您对 Cisco 300-425 On-Demand Exam 的准备情况： https://www.trainingdump.com/Cisco/300-425-practice-exam-dumps.html

类别 300-425

[Q28-Q42] Try 100% Updated 300-425 Exam Questions [2026]

[Q31-Q53] 免费思科 300-425 模拟考试题库 [2022 年 11 月 19 日］

思科 300-425 认证考试有哪些优势

您可以使用哪些学习指南来学习 300-425 专题？